4/19/2021 0 Comments Lg Flatron Tv
In order to get the best possible experience our LG.COM website please follow below instructions.
Lg Flatron Tv Upgrade To AIf youre using Internet Explorer 9 or earlier, you will need to use an alternate browser such as Firefox or Chrome or upgrade to a newer version of internet Explorer (IE10 or greater).Do not include any personally identifiable information, obscenities or spiteful comments.Avoid writing about installation or customer service: contact us instead. Check with your local retailers for final price and availability. Youll get rave reviews for the high-functionality, power and style of LG TVs. If you want to connect to LG Corp., or other LG affiliates, please click. WARNING BE CAREFUL ELECTRIC SHOCK There are some special components used in LCD monitor that are important for safety. These parts are If you want to replace with the new backlight (CCFL) or marked on the schematic diagram and the inverter circuit, must disconnect the AC adapter. ![]() Carefully bend each IC lead against the circuit foil pad and solder it. This technique to the circuit board causing the foil to separate from or involves the installation of a jumper wire on the lift-off. Test method This specification is applied to 1922 Wide Monitor TV used LP69G chassis. Performance: LGE test method followed 3.2 Demanded other specification 2. Type Separate Sync., Digital Operating Frequency Analog Horizontal 28 83kHz Vertical 56 75 Hz Digital Horizontal 28 83kHz Vertical 56 75 Hz Resolution(M198WA) Analog Max. Hz Recommend 1440 x 900 60Hz Digital. Unit Remark Type TFT Color LCD Module Active Display area 473.76 (H) x 296.1 (V) Outline dimension 493.7 (H) x 320.1 (V) x16.5 (D) Pixel pitch 0.282mm (H) x 0.282mm (V) x RGB Color arrangement RGB vertical stripe Color Depth. Push the button. 2. After push the cable management like above fig.(Downward), Disassembly the Cable management with pulling it upward. Disassembly Cable Holder. Application Range This specification sheet is applied to 19 20 22 LCD Monitor TV which is manufactured in TV (or Monitor) Factory or is produced on the basis of this data. Specification 1) The adjustment is according to the order which is designated and which must be followed, according to the plan which can be changed only on agreeing. NO POWER (LED INDICATOR OFF): A Process Fail Check 15V or Check 15V or ST5V of Power BD. ST5V of Power BD. Pass Fail Fail Re-soldering of Change Check Output of Check short of defect part of IC100, Q307. On Display Unit. Pass Fail Change Panel Link Cable Check Panel Link Cable or Module. Module. Pass Check Inverter Fail Change Inverter Connector Connector or inverter. Pass Re-soldering or change the Fail Check the inputoutput of defect part, Check the. Fail Check the input output Check the J900. ![]() R125. Pass Re-soldering or change the Fail Check the inputoutput of defect part, Check the IC100. Pass Re-soldering or change the X100 Fail Check the input output defect part, Check the of R100. X100. Pass Check input source cable and jack. No Raster on AV(Scart in 7. Pass Re-soldering of Change the Fail Check inputOutput defect part, Check the ofIC100. X100 Pass Fail Re-soldering of Change Check the input output the defect part. Power Supply Block (LIPS) This Block Generates DC Voltage (5V,15V) to Main Control system from AC Power (100-240 V, 5060 Hz, 1.0A) 2. DCDC Converter block DCDC Converter convert the input 5V,15V to proper 1.8V,2.5V,3.3V,5V,10.5V for Main control system. EMI components. This part contains of EMI components to comply with global marketing EMI standards like FCC,VCCI CISPR, the circuit included a line-filter, across line capacitor and of course the primary protection fuse.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |